Vinyl Plank Flooring Gaps: Causes, Fixes and Prevention

Article tag: en Article tag: vinyl plank flooring gaps
Vinyl plank floor with a visible seam gap

A small gap that opens in winter and closes again in summer is usually normal movement in a floating vinyl plank floor. A gap that stays open all year, keeps growing, or shows up with raised edges points to a cause you can find: temperature swings, an installation problem, or something pinning the floor in place. Below you will find how to tell the difference, what to do about each type, and how to keep new gaps from forming. If your floor was installed in Northeastern Pennsylvania, where heating season swings indoor conditions hard, we can help you work out which kind you have.

Giantfloor
Find Flooring That Fits Your Space
Giant Floor offers waterproof vinyl, hardwood, and carpet, with personalized quotes and flooring options for homes and businesses in Northeastern Pennsylvania.
Visit

Key Takeaways

  • Small seasonal gaps on a floating floor are movement, not failure. Gaps that stay open year-round deserve a closer look.
  • The usual causes are temperature swings, poor acclimation (letting planks adjust to the room before installing), the wrong adhesive on glue-down floors, and a floor that cannot move freely.
  • Do not fill the joints between floating planks with rigid filler. Close the gap by moving the planks, or use a product the flooring maker approves.
  • Photograph the gap and note the date before you repair anything. Early reports to your installer or retailer protect your warranty options.
  • Stable room temperature and a clear perimeter gap prevent most gap problems.

Table of Contents

Is it normal to have gaps in vinyl plank flooring?

Sometimes. Vinyl planks react to temperature, installation conditions and the surface beneath them. A tiny, occasional gap does not always mean the floor has failed, but noticeable or growing gaps warrant attention.

Here is a simple way to sort what you see:

What you notice Likely meaning What to do
Hairline gaps in January that close by summer Seasonal contraction of a floating floor Steady the room temperature and check that nothing pins the floor
A gap you can slide a coin into, open all year Installation, subfloor or movement problem Document it and have the floor assessed
Gaps near a door, window or vent Local temperature or sunlight effect Reduce the exposure and monitor
Joints raised along with gaps Peaking from acclimation or environment Contact the installer or retailer
Gaps over a soft or uneven spot Subfloor issue Level the area before any cosmetic repair

The point is not the width alone. It is whether the gap moves with the seasons, where it sits, and whether the planks around it are still flat and locked together.

Why vinyl plank gets gaps

Temperature and humidity

Vinyl is a material that grows and shrinks with heat. Humidity and temperature changes can make planks contract, which opens gaps along the sides, while humidity or heavy foot traffic can shift plank ends apart, more often on click-lock floors than on adhesive ones.

In Scranton, Wilkes-Barre and the Poconos, a house can sit cold during a winter vacation, run hot once the furnace works, and then get direct afternoon sun through a south-facing door. A floor that goes through those swings will move. Rooms with large glass doors and unheated sunrooms are the usual trouble spots. We cover the cold-season side in our NEPA winter flooring guide and in a related piece on winter gaps in hardwood floors, where the same seasonal logic applies.

Temperature and humidity

Poor acclimation

Acclimation means letting the planks sit in the room where they will be installed, at normal living temperature, so they adjust before you lock them together. ARDEX, an adhesive and floor-prep manufacturer, states that failure to properly acclimate the tiles, planks and installation area is the most common culprit behind peaking and curling, where joints lift about a quarter inch while the rest of the floor stays bonded. ARDEX also notes that no adhesive can be expected to completely restrain planks from moving, so the defense is acclimation plus a test area.

If planks were installed straight from a cold truck or a cold garage, the floor can look perfect on day one and open up as it settles to room temperature.

Adhesive and subfloor problems on glue-down floors

On glue-down vinyl, the wrong adhesive or a poorly prepared subfloor lets planks creep. On floating click-lock floors, a low spot or a bump in the subfloor can keep joints from fully engaging, and the seam opens where the plank flexes. Concrete subfloors bring moisture and flatness questions of their own, which we explain in our guide to installing vinyl flooring over concrete.

A floor that cannot move

A floating floor needs room to expand and contract around its edges. When trim is nailed down over the planks, a cabinet sits on top of the floor, or the perimeter is packed tight against a wall, the movement has nowhere to go. It then shows up as a gap somewhere else, or as peaking.

Heavy furniture can do the same thing. A loaded bookcase or a bed with wide feet can pin a section of floating floor, so the planks pull apart nearby. Raising and spreading the load helps, and there are furniture risers made to protect floors that are worth a look when you are rearranging heavy pieces over a floating floor.

How to tell what is behind your gaps

Spend ten minutes on this before you touch anything:

  1. Check the calendar. Gaps that appear in cold months and close when it warms up point to temperature.
  2. Check the location. Gaps clustered near an exterior door, a large window or a heat vent suggest a local temperature effect.
  3. Run your hand along the seam. Raised edges, a hollow sound or a plank that rocks suggest a subfloor or acclimation problem.
  4. Look at the edges of the room. Is there trim pressed down on the planks, or a floor butted tight to a wall or cabinet base?
  5. Check what sits on the floor. Heavy furniture, a kitchen island or a floor-mounted fixture can lock the floor.
  6. Photograph and measure. Take clear photos with a coin or ruler for scale and write down the date.

That last step matters more than it seems. If you notice issues within a few days of installation, contact your installer or flooring store right away, document the date and take photos, and avoid doing repairs yourself, which can void warranties. Most installation warranties cover defects found in the first year or two.

How to fix gaps in vinyl plank flooring

The right fix depends on where the gap is and what kind of floor you have. The method also differs between click-lock floors and glued floors.

Gaps at the ends of planks

For end-plank separation on a floating floor, vacuum the gap, attach a suction cup to one board and tap the cup with a rubber mallet to nudge the planks back together. If the gap reopens within days, something is still pulling the planks apart, so look for the cause before repeating the fix.

Four steps for closing an end-plank gap

Gaps along the sides

For side separation, the same source suggests cleaning the gap, letting it dry overnight, applying a putty rated for vinyl flooring and foot traffic, and scraping off the excess with a plastic putty knife. Use this for cosmetic gaps that are stable, not for a floor that is still moving.

Choosing a filler

“Vinyl floor gap filler” is not one product. Depending on the flooring and the location, the right answer might be a flexible sealant, a vinyl seam sealer, a replacement plank or a transition strip. Three rules keep you out of trouble:

  • Follow the flooring manufacturer’s installation and maintenance instructions for which product is approved.
  • Use a product that sticks to vinyl, tolerates foot traffic and stays flexible.
  • Never use wood putty, grout or any rigid filler in a joint that needs to move.

A rigid fill at the perimeter can stop the floor from expanding, which leads to buckling, peaking or new gaps elsewhere. For a gap along the wall, quarter-round or baseboard molding is the cleaner cover. It hides the expansion space without locking it. We carry molding at our showroom, so you can match it to your plank color.

Planks that are damaged or badly separated

If a plank is cracked, a joint is broken or several planks have drifted apart over a long run, replacing the affected planks or re-laying a section is the lasting fix. Floating floors can usually be unlocked back to the problem area, which is one reason to keep a few spare planks from the original order.

When the cause is the subfloor

Gaps over a dip, a bump or a damp patch come back no matter how well you fill them. The subfloor needs leveling or moisture correction first. Replacing vinyl on top of existing vinyl has its own rules, and our page on laying vinyl flooring over vinyl flooring explains when it works.

What if the gap is a warranty or installation issue?

Most flooring makers route claims through the retailer. Armstrong, for example, tells customers with a floor problem to return to the retailer with the sales receipt, and notes that problems caused by installation or on-site conditions fall outside the product warranty. That is why your photos, your dates and your installation paperwork matter. Keep the receipt, the product name and number, and the date of installation.

If your floor came from us, bring the photos to the showroom or contact us, and we will go through what you are seeing and the likely cause.

How to prevent gaps in vinyl plank

Most gaps are decided before the first plank goes down. Whether you are planning a new floor or deciding what to do when one is replaced, this is the routine that matters:

  1. Acclimate the planks. Bring unopened cartons into the room and follow the maker’s required time and temperature range.
  2. Hold a stable temperature. Keep the room at livable heat before, during and after installation. Setting the thermostat back to a very low temperature while a house is empty in January invites movement.
  3. Prepare the subfloor. Flat, clean and dry beats any cosmetic fix later.
  4. Match the adhesive to the product. On glue-down vinyl, the wrong adhesive is a leading cause of gaps. Use what the plank maker specifies.
  5. Leave the perimeter gap. Floating floors need an expansion gap around the walls and fixed objects. The exact size is in the product’s instructions, and trim covers it.
  6. Do not pin the floor. Fasten trim to the wall, not through the planks, and keep cabinets off floating floors.
  7. Control sun and humidity. Blinds on sunny doors and steady indoor humidity reduce stress on the joints.

Winter work needs a few extra steps in our region, and we explain them in Can You Install Flooring in Winter? Myths vs. Facts.

Our perspective

Most of the gap calls we hear about come down to the same few things: planks that did not get to adjust to the room, a house whose temperature swings too much, or a floor that has no room to move. That is why we treat the product choice and the installation as one decision.

In Northeastern Pennsylvania, heating season is hard on every floor. We help you choose a vinyl plank that fits the room, whether that is a basement, a kitchen or a sunroom, and we offer personalized, no-obligation quotes so you know the scope before you commit.

Because we keep a large in-stock selection and offer quick installation, you can see the planks in person at the showroom and move from choosing to installing without a long wait. Spare planks from your order are worth keeping, and we are glad to talk about that when you pick your floor.

the author

Getting a floor without the gap problem

If your gaps are the kind that need a lasting fix, or you are ready to replace a floor altogether, we sell waterproof luxury vinyl and install it across Scranton, Wilkes-Barre, the Poconos and the surrounding counties. Browse the vinyl flooring collection to see what is in stock, or get a personalized, no-obligation quote through Giant Floor.

Pocono Pine #2024

We serve homeowners, landlords with multiple units, contractors and businesses. We also offer White Glove Delivery, and our installation team covers residential and commercial jobs. Local project pages, such as our Swiftwater vinyl floor installation page, show the areas we work in.

Protecting your floor after the repair

Once your gaps are sorted, a few habits keep them from returning:

  • Keep the room temperature steady through the winter, even in rooms you rarely use.
  • Use felt pads under furniture legs and spread heavy loads. Our guide to the best area rugs for vinyl plank explains which rug backings are safe on luxury vinyl.
  • Clean seams with a vacuum, not a wet mop, so water does not sit in the joints.
  • Walk the floor each season and photograph any change early.

A cold-feeling floor also encourages people to crank the heat, so if comfort is part of why you are replacing, see how vinyl plank compares on warmth.

FAQ

Why does LVP get gaps?

The common causes are temperature swings, poor acclimation, the wrong adhesive on glue-down floors, and a floor that cannot expand because trim, furniture or cabinets pin it. Humidity and heavy foot traffic can also shift plank ends on click-lock floors.

What can I use to fill gaps in vinyl plank flooring?

Use a putty or sealer rated for vinyl and foot traffic, and follow your flooring maker’s instructions. Avoid wood putty, grout and rigid fillers in any joint that needs to move. For gaps along the wall, quarter-round or baseboard molding is the better cover.

Why is my vinyl plank flooring coming up at the seams?

Raised seams, or peaking, are most often tied to poor acclimation or a floor with no room to expand. The joints lift while the rest of the floor stays flat. Document it with photos and contact your installer or retailer.

Should I fix gaps myself or call the installer?

If the floor is new, call the installer or retailer first and take photos, because DIY repairs can affect warranty options. For an older floor with a small, stable cosmetic gap, a suitable vinyl putty is a reasonable repair.

Sources

Share